Nullam dignissim, ante scelerisque the is euismod fermentum odio sem semper the is erat, a feugiat leo urna eget eros. Duis Aenean a imperdiet risus.
The compression ratio is the reason this gate type exists. Panel count scales with the span; the retracted stack height stays manageable regardless of how wide the gate is extended. No other gate format handles a 30- or 40-meter opening from a 2-meter footprint.
The material choice drives different things: aluminum for weight and corrosion resistance, stainless for surface hardness and chemical tolerance. More on this below.
Standard production covers most industrial and commercial opening dimensions. Custom configurations are available on engineering review for spans or heights outside that range.
24V DC or 220V/110V AC drive, rack-and-pinion or chain system. Soft-start and soft-stop reduce the mechanical shock load on accordion joints at end of travel — relevant for long-service-life expectations on high-cycle sites. Manual release is standard for power-failure operation.
RF handsets to 50 meters, card reader access, PIN keypad, inductive loop for automated vehicle sensing, dry contact and RS485 outputs for building management integration. Specified at order; the gate hardware accommodates all of them.
The gate arrives on its caster system, pre-assembled. Fixed anchor at one side of the opening, motor and control wiring, then magnets or rails, done. An experienced two-person crew typically commissions a 10 to 20 meter span in four to six hours.
This is a question that comes up on almost every retractable gate inquiry, and the answer usually isn’t as complicated as it sounds once you know what drives it.
Aluminum is the right call for the majority of industrial and commercial sites. The weight difference across 20 or 30 accordion panels is significant — aluminum runs roughly 40 percent lighter than stainless at the same cross-section. On a large retractable gate, lighter panels mean the casters are carrying less load on every cycle, the motor is working within a more comfortable range of its rated capacity, and the accordion hinge pins are under less stress each time the gate extends or compresses. Those are not marginal differences when you’re running a site entrance that cycles dozens of times a day. The surface doesn’t rust; the powder coat handles UV and abrasion in standard outdoor environments.
Stainless steel comes up when the environment is genuinely aggressive in ways that aluminum powder coat doesn’t handle well. Food processing facilities where the gate gets hosed down with industrial cleaning agents. Chemical plants where liquid splash hits the frame surface. Coastal logistics hubs where the salt air concentration is high enough that even powder-coated aluminum shows surface degradation over time. Public infrastructure where the specification requires a polished or brushed metal finish that can’t be replicated with paint. In those situations, the surface hardness of 304 stainless and its resistance to chemical attack justify the weight and cost premium.
Where it gets muddled is when stainless is specified purely because it sounds more industrial or more durable, without a clear reason from the site conditions. If the gate is going into a dry inland warehouse with no chemical exposure, aluminum does the same job at lower weight, lower motor load, and lower cost. The right answer depends on what the gate is actually being exposed to — not on which material sounds heavier-duty.
The gate can be pushed manually, but for commercial and industrial applications, the motorized configuration is almost always what gets installed. The manual option stays available for sites with intermittent use or no reliable power supply.
The motor mounts to the leading post — the mobile end of the gate that carries the lock. Drive is through rack-and-pinion or chain depending on the configuration. Soft-start prevents the accordion structure from lurching when the motor engages; soft-stop prevents it from slamming into the end stop at full retraction. Over thousands of cycles, those two features are what keep the hinge pin connections from loosening ahead of schedule.
On the control side, the usual industrial access scenarios are all covered. RF remote handsets for security personnel or maintenance staff moving around the site. RFID card or fob readers for driver access without leaving the cab. PIN keypad for personnel on foot where card systems aren’t practical. Inductive loop detectors in the approach surface for fully automated vehicle sensing — the gate opens when a vehicle arrives, closes after it clears. For sites running a building management system, RS485 or dry contact outputs connect the gate controller to site-wide scheduling and event logging.Battery backup is an available option for sites where a power cut during active security hours is an operational problem rather than just an inconvenience. Worth specifying upfront rather than retrofitting later.
Technical Item |
Specifications & Details |
| Gate Type | Industrial Retractable Gate (Accordion / Folding Structure) |
| Frame Material | 6063-T5 Aluminum Alloy or 304 Stainless Steel (both available) |
| Surface Finish | Industrial powder coating (aluminum) or brushed / polished finish (stainless steel); custom RAL colors available |
| Maximum Extended Length | Up to 40.0 meters (standard range 2 m – 40 m) |
| Gate Height | 1.2 m to 2.2 m (customizable to site requirement) |
| Retracted Footprint | Approximately 3–5% of extended length depending on panel count |
| Drive System | Electric motor (24V DC or 220/110V AC) with rack-and-pinion or chain drive; manual push option available |
| Motor Features | Soft-start / soft-stop; thermal overload protection; manual release for power-failure operation |
| Control Options | RF remote (up to 50 m range), RFID reader, PIN keypad, loop detector, intercom, BMS integration (dry contact / RS485) |
| Smart Compatibility | Compatible with major smart access platforms and industrial building management systems |
| Safety Features | Infrared photocell sensors, auto-reverse on obstacle, manual emergency release, optional battery backup |
| Cycle Rating | Rated for continuous high-frequency industrial duty cycle operation |
| Application | Manufacturing plants, logistics warehouses, school campuses, stadiums, government facilities, commercial perimeter access, parking structures |
| Customization | Extended length, height, frame material, surface finish, RAL color, drive system, control interface, safety accessories |
The retractable gate is the gate type with the shortest civil works requirement. There is no foundation post to cast, no overhead beam to level and anchor, no ground channel to cut across the driveway surface, magnets or rails installed. The gate ships pre-assembled on its caster system, in accordion form, ready to position at the opening.
What the installation actually involves: fixing the anchor post to the wall or structural column on the fixed side of the opening, running the motor and control wiring to the drive unit and access control devices, and commissioning the motor limits and control programming,magnets or rails installation. On a level concrete surface, two people who have done this before typically finish a 10- to 20-meter span in four to six hours. That’s installation and commissioning combined — not installation one day, commissioning another.
Longer spans and uneven ground conditions change the calculation. For spans above 20 meters or sites with surface variation that the standard caster hardware doesn’t accommodate, JHR supplies leveling hardware with the caster assemblies and provides installation drawings based on customer-supplied ground plans. Remote engineering support is available throughout — not as a paid add-on, but as part of the order process.Extended length, gate height, material preference, drive system, and site location are the inputs needed to generate a specification and quote. Turnaround is one working day from inquiry.
18/ September
11/ September
4/ September
28/ August
